Home › Topics › 無線電遙控 › How to Build and Optimize a Kyosho HOR

How to Build and Optimize a Kyosho HOR

Kyosho HOR 1/8 RC motorcycle: assembly, electronics and track tuning

Kyosho's HOR (Hanging On Racer) is one of the few 1/8 electric RC motorcycles that stands up on its own — no training wheels, no stand. It works through SDSS (Semi-Direct Steering System): when the bike leans, the front wheel steers into the lean, and the rider figure shifts its weight to the inside of the corner[1]. This guide follows the three "華Dee" build videos from Hong Kong's RCMCHK club, covering the kit, the electronics and track tuning[3][4][5].

[ edit intro ]

🧰 What you need before opening the box

[ edit ]

The HOR is a kit: the box contains the chassis, body, rider and three pinion gears (10T/12T/14T). Everything else is extra. Kyosho's official "Requirement to Run" list[1]: a 2-channel radio (recommended No.82147), one servo (GPW21), an ESC (GPW17), a 7.2V 1600mAh NiMH pack (No.71351), a charger (No.72204 with GPW18 adaptor), grease (No.96508), paint and hand tools. The Le Mans DM20 motor is included — the real hidden cost is radio, servo, ESC, battery and charger.

📐 Stock specifications

[ edit ]

Length 270mm, width 98mm, height 190mm, wheelbase 185mm, tyre F Φ78×18mm / R Φ86×23mm, gear ratio 13.80–19.30:1, weight about 750g, motor Le Mans DM20[1]. Two numbers matter: the front tyre is smaller than the rear (78 vs 86mm) so it can turn faster, and the wide gear ratio range lets the same motor be tuned for torque or top speed simply by changing the pinion.

Eight build steps
The eight build steps — sequence matters, especially the servo and steering linkage.

🔧 Step one: chassis and front fork

[ edit ]

Fit the fork to the steering head, then check that both legs have the same preload: press them together, and they should rebound at the same rate. Uneven forks guarantee a bike that pulls to one side. Do not overtighten the steering bearings — the head should move freely with no play. Too tight and the servo fights the steering, producing understeer; too loose and the bike weaves on the straight.

🏍️ Step two: frame, motor mount and gears

[ edit ]

Mount the motor before fitting the pinion. Set gear mesh with a 0.1mm strip of paper between the teeth: tighten, pull the paper out, and you should feel slight resistance. Too loose strips teeth; too tight overheats the motor. Pinion choice: 10T for torque (small tracks), 12T stock, 14T for top speed (long straights, but hotter motor and ESC). Start with 12T.

⚙️ Step three: servo, linkage and centre

[ edit ]

The most common mistake: power the servo and let it centre before fitting the arm. Fit the arm at an angle and every steering input becomes asymmetric — no amount of EPA will fix it. Check that left and right throw are equal; if one side is shorter, adjust the linkage ball ends rather than using trim. Trim corrects straight-line drift, not throw.

Fitting the servo arm
Centre the servo first, then fit the arm and linkage (still from the build video).

🔌 Step four: ESC and wiring (GPW17)

[ edit ]

The GPW17 is tuned for the bike and includes a 6V/1A BEC for the servo and receiver. Its protections[2]: on 2S LiPo it drops output to 50% below 6.5V and cuts at 6.0V; on 3S, 9.75V and 9.0V; on 5–9 cell NiMH, 4.5V and 4.0V; and it cuts output if the ESC exceeds its factory temperature for five seconds.

Kyosho specifies a 7.2V NiMH pack[1] while the ESC also supports 2S/3S LiPo[2]. LiPo works, but three cautions: higher voltage means more heat at the same gearing, the low-voltage cutoff must be set correctly (6.5V for 2S), and LiPo needs balance charging and safe storage. Beginners are better off with NiMH.

Throttle calibration: radio on, full throttle, power the ESC (first tone), full brake (second), neutral (third). Skip this and the bike will launch the moment you switch on.

⚖️ Why doesn't it fall over?

[ edit ]

There is no gyro inside. Three physical effects keep it upright: steering geometry — the fork is raked back, so the contact patch sits behind the steering axis, and the front wheel steers into the lean; rider weight — the servo pushes the figure to the inside of the corner, shifting the centre of mass; and wheel gyroscopic stability, which increases with speed. That is why slow speed is always the hardest part — it is physics, not a faulty bike.

Three forces
Steering geometry, rider weight transfer and wheel gyroscopics.

🎯 Track tuning: change one thing at a time

[ edit ]

Change one setting, run two laps, note the result, then change the next. The five symptoms below cover most problems: straight-line weaving (excess steering play, loose fork, deformed tyre), corner-entry understeer (insufficient throw, rider too stiff, front tyre glazed), exit oversteer (too much throttle, hard rear tyre, fast rebound), steering that will not centre (servo not centred, binding linkage), and power fading after a few minutes (ESC thermal cut or battery cutoff)[2].

Steering throw (EPA/dual rate) is the most commonly mis-set value. Too much and the bike turns in too sharply and falls; too little and it will not make the corner. Start at 60% and increase until the bike clears the tightest corner on the track.

Rider spring tension sets how fast weight transfers: too stiff and the bike understeers on entry; too soft and it wallows. Fork preload controls dive under braking — stiffer for smooth surfaces, softer for bumpy ones.

Five symptoms
Symptom table: what to change first.

🛞 Tyres and surfaces

[ edit ]

The front and rear tyres are different sizes (Φ78×18 vs Φ86×23) and are not interchangeable[1]. Stock tyres work best on clean asphalt or carpet tracks; once the tread picks up dust, grip falls off a cliff, so wiping the tyres with tape or cleaner before each run is worth more than any hop-up. In Hong Kong, club running happens at tracks such as ACO Racing Track in Fanling and indoor venues, and RCMCHK runs an annual Fun Day with multiple classes[6]. For a first visit, watch a heat before driving.

Launching the bike
Launch with a little forward speed — holding the tail and letting go (still from Ep. 2).

🔋 Batteries and runtime

[ edit ]

The stock 7.2V 1600mAh NiMH pack gives roughly 8–12 minutes depending on gearing and throttle. Three habits: do not run to a dead stop (NiMH cells can false-peak), let packs cool for ten minutes before charging, and store them at about 6V rather than fully charged for months.

🧯 Five common faults

[ edit ]

Bike launches on power-up — throttle not calibrated; redo the three-step calibration. Steering asymmetric — the arm was fitted off-centre; refit after centring. Power fades after minutes — thermal cut or battery cutoff; check ESC temperature[2]. Will not track straight — uneven fork preload, deformed tyre or steering play. Stripping noise — gear mesh too loose or motor screws loose.

🛠 After each run

[ edit ]

Wipe the bike and tyres, check every screw (the vibration is significant, especially the motor mount and servo arm), clean and re-grease the drivetrain, remove the battery, and write down the setup (EPA, pinion, tyres). Starting the next session from a written baseline saves hours.

📺 How to watch the three videos

[ edit ]

Part 1 takes you from zero through the chassis, servo and linkage[3]; the Advance edition (with subtitles) covers detail and common mistakes[4]; Ep. 2 is track footage showing launch technique and lines[5]. Build along with Part 1, check your work against Advance, then watch Ep. 2 before your first run.

❓ FAQ

[ edit ]

Can I fit a brushless motor?
Mechanically yes, but the GPW17 is designed for the brushed DM20; you would need a new ESC, and the transmission may not take the extra torque. Not recommended for beginners.

Why does it fall as soon as I let go?
Not enough speed. Gyroscopic stability rises with wheel speed — launch with some forward motion.

Can I run 3S LiPo?
The GPW17 supports it (9.75V/9.0V cutoff)[2], but the motor and gearing will run hot unless you drop pinion size.

Are front and rear tyres interchangeable?
No — Φ78×18 front, Φ86×23 rear[1].

How long does the build take?
Three to four hours with experience; for a first build, split it over two evenings so glue and threadlock can cure.

📚 References

[ edit ]
  1. Kyosho 1/8 HOR series product page — SDSS, technical data (270×98×190mm, 185mm wheelbase, Φ78/Φ86 tyres, 13.80–19.30:1, 750g, Le Mans DM20), kit contents and requirement to run
  2. Kyosho GPW17 speed controller instruction sheet (PDF) — 6V/1A BEC, 2S/3S LiPo and 5–9 cell NiMH cutoffs, thermal protection
  3. RCMCHK: 華Dee 入門手冊 How to build a Kyosho HOR — Part 1
  4. RCMCHK: 華DEE 入門手冊加強版 How to build a Kyosho HOR — Advance (with subtitles)
  5. RCMCHK: 華DEE 入門手冊加強版 How to build a Kyosho HOR — Advance Ep. 2
  6. Timway Wiki: The R/C Motorcycle Club of Hong Kong (RCMCHK)

🎥 Videos

3 related videos · click to play

If you spot an error or have an editorial suggestion, please submit a correction.