S.D.S.S. (Semi-Direct Steering System) is the steering arrangement Kyosho uses on its 1/8 scale Hanging-On Racer (HOR) electric RC motorcycles[1]. It works because the whole mechanism follows the physics of countersteering, letting an RC bike lean into a corner the way a real motorcycle does instead of forcing the front wheel toward the apex.
🔧 Why a two-wheeler cannot steer directly
[ edit ]A four-wheeled car keeps all four tyres on the ground, so turning the front wheels simply changes its direction; the body barely has to lean. A two-wheeler has no such luxury: it has to lean first so that gravity balances the centrifugal force pushing it out of the corner.
If a bike used a rigid direct linkage, turning the bars left at speed would push the front contact patch left while the centre of mass stayed put. The upper body is then thrown the other way in a violent high-side and the bike crashes. The same physics applies to a real motorcycle and to a 1/8 scale model; the difference is that the model has no rider to correct it.
🔄 Countersteering: to go left, push right
[ edit ]On a single-track vehicle the first steering input points the front wheel slightly to the outside of the turn. Turning left, the wheel first goes right, the bike falls to the left because of inertia, and once it is leaning the fork geometry (rake and trail) brings the wheel back into the corner[4]. The whole sequence takes a fraction of a second, which is why the rider only perceives "steer left, go left".

⚙️ The four steps of S.D.S.S.
[ edit ]1. Counter-push. You steer left; the servo pulls the spring linkage and pushes the front wheel right first. That is deliberate — it creates the condition for the bike to lean[1].
2. Weight shift. With the contact patch moved to the right of the machine, inertia tips the upper body the other way, so the whole bike leans left.
3. Geometry recovery. Once the bike is leaning, rake and trail bring the front wheel back toward the inside of the turn, while the spring linkage gives the fork room to settle into a stable line.
4. Exit. Release the steering input, the spring relaxes, and forward momentum plus gyroscopic effect stand the bike back up.
🆚 Why "semi-direct" rather than fully direct
[ edit ]"Semi-direct" means the servo is not rigidly bolted to the fork: motion is passed through a spring linkage. That absorbs the servo's abrupt movements and gives the fork enough freedom to find its own balance point[1].
A rigid link transmits every small servo movement straight into steering angle, which easily provokes oversteer at speed; a fully soft link loses directional precision and makes turn-in vague. Semi-direct sits between the two.

🏍️ How it is built on the Kyosho HOR
[ edit ]The HOR uses a twin-tube main frame, a sprung front fork, an asymmetric rear swingarm with a mono-shock friction damper and a real chain-and-sprocket drive. On top of that, S.D.S.S. routes the steering servo through the spring linkage instead of locking the fork solid[1][2].
The complementary part is the "hanging-on" rider: a figure built from 13 connection points that leans off the saddle into the turn with the bike, moving weight toward the inside of the corner like a Grand Prix rider[1]. Rider and fork move together, which is what keeps the HOR controllable even at low speed.
🛠️ What to watch when tuning
[ edit ]Spring rate is the main variable: a softer spring adds cushioning between servo and fork and suits low-grip surfaces or new drivers; a harder spring sharpens response on high-grip tracks but demands smoother input. Excessive play in the linkage shows up as a delay where the bike has turned but not yet changed direction.
Fork height, tyre wear and servo centre all move the effective turn-in point. Change one thing at a time and repeat on the same surface, otherwise it is impossible to tell which adjustment actually helped.
❓ FAQ
[ edit ]Q: Is S.D.S.S. the same as self-balancing?
A: No. It only cushions the servo's output to the fork. Balance still comes from speed, gyroscopic effect and fork geometry.
Q: Can I convert it to a rigid link?
A: Technically yes, but the bike highsides far more easily at speed. The stock semi-direct layout is a compromise between response and control.
Q: Why does the front wheel turn right when I steer left?
A: That is countersteering. The wheel points outside the turn first so the bike falls into it, then geometry brings the wheel back.
Q: Does it behave the same at low speed?
A: No. With less gyroscopic effect, lean depends more on geometry and weight transfer, so turn-in feels slower and has to start earlier.
📚 References
[ edit ]- House of RC — Kyosho Motorcycle Hanging On Racer (HOR) product notes: S.D.S.S. and the 13-point rider figure
- Kyosho RC — Hanging On Racer model lineup
- Kyosho — Hanging On Racer instruction manual index
- Berkeley Physics — Steering in bicycles and motorcycles
- RC Car Action — Kyosho 1992 S.R.T. Suzuki RGV 1/8 kit
- YouTube — Hong Kong RC motorcycle group, Hanging On Racer
🎥 Videos
4 related videos · click to play
Play


